Mobile: 18688976300 (Mr. Peng) 15222276387 (Mr. Bai)
Email: pengwl@honred.com
QQ: 176496342
Address:Building A1, Runteng Industrial Park, Shiyan Street, Bao'an District, Shenzhen
Bottom line first: single-use endoscopes move disassembly from service to manufacturing. The product is deliberately built so it cannot be opened and reused, yet the plant needs to open it more often than a reusable device ever does — incoming inspection opens it, failure analysis opens it, rework opens it and seals it again. The same M0.8-M1.2 screw that is a wear part on a reusable scope is a piece of evidence here, and how cleanly it comes out decides whether the unit ships or is scrapped.
A reusable scope is torn down to restore function: new seals, new lens, re-sterilisation, and opening it has value. A single-use device is the opposite, because it has to demonstrate that it cannot be reopened. Clips are one-way, housing halves are ultrasonically welded or UV-bonded, and screws are often buried under adhesive. The regulatory position is equally plain: a device labelled single-use sterile is not to be reprocessed, and in-house reprocessing is non-compliant, which removes any commercial motive to open it again.
That does not mean there are no screws. The image-module bracket has to be locked after focus adjustment, the pull-wire anchors in the bending section have to be adjustable in preload, and the LED board and handle PCB rely on clamping force to hold contact resistance. These are almost always M0.8-M1.2 self-tapping or machine screws, four to twelve per device. Few in number, but each sits in a very tight space, often next to an optical surface or a flex circuit.
So three disassembly needs appear on the manufacturing side, and all three share one property: the purpose is not to repair the product but to obtain information or to strip out a non-conforming unit. That is why single-use lines have started buying small-format removal equipment in batches — the demand grew out of quality and process engineering, not out of the service department.
A single-use bronchoscope has an insertion tube of roughly 5.1 to 5.8 mm outside diameter, and the usable height inside the handle is often under 20 mm, with the image module and bending mechanism packed together. In that envelope the first constraint on the tool is not torque but diameter. A cross-head bit for M1.0 runs 1.4 to 1.6 mm across the shank, and with a guide sleeve that becomes 2.0 to 2.4 mm, which will not enter when the wall between the screw hole and the next feature is only 0.4 mm.
What is left is a slender unsleeved bit with low speed and axial compliance. Such bits have a high length-to-diameter ratio and poor stiffness, so they whip at speed, and once runout passes 0.02 mm the cross recess engages only two flanks and cam-out at breakout is almost certain. The working range is 30 to 80 rpm: stability comes from low speed, not from forcing torque.
Angular misalignment is the second hidden constraint. Beyond 3 degrees between bit axis and screw axis, contact drops from four flanks to two and local stress doubles, and plastic bosses crack far more readily under that offset load. A bench machine wins here simply because the workpiece attitude can be set precisely, and the value of small screw removal equipment at this size lies in a low minimum starting torque and a stable low-speed band rather than in replacing hands with automation.
The first obstacle is adhesive. A dot of threadlocker or UV adhesive on the head is common, to keep the screw from loosening under transport vibration and bending motion. UV adhesive is brittle and the breakout curve shows a sharp peak followed by a collapse; anaerobic adhesive is tough and the curve climbs slowly. Guess the adhesive type wrong and apply standard torque, and cam-out is the likely outcome.
The second obstacle is a very narrow thermal window. A reusable device can be heated past 120 degrees Celsius to soften the bond; a single-use device cannot, because the lens stack, the ABS or PC housing and the flex circuit will not take it. The usable ceiling is usually 60 to 70 degrees Celsius, which barely reduces the breakaway torque of most anaerobic adhesives while already approaching the glass transition of the plastic.
The third obstacle comes from sterilisation. Ethylene oxide residues require structures that trap little gas, so designs favour through-holes and thin walls, and screw holes are often through-holes. A through-hole means a short engagement length and few threads in contact, so the thread reaches plastic deformation earlier during breakout. And once opened, the device has lost its sterile and sealed state: whether or not it can be reassembled, it can no longer ship as product.
Incoming and first-article inspection needs reversibility and records. Open it, look, record, decide — peak torque, snug-point angle and total rotation have to be logged per screw, or the conclusion cannot be reproduced. Cycle time is not the issue here; completeness of the record is.
Failure analysis needs non-destructive work and preserved fracture surfaces. The fracture face, the adhesive morphology and the thread damage are all evidence, and the disassembly itself must not create new damage. Slower is better, ideally with macro imaging before, during and after. These stations also have to handle non-standard structures, so recipe management matters more than throughput.
Line rework needs cycle time and changeover. One line may run several models whose handles differ by a few millimetres, which shifts every screw position, and manual locating does not scale. What a vision machine does here is identify the model first and then fix the coordinates. The real threshold for an automatic vision screw removal machine on a mixed line is not camera resolution but whether a recipe can be switched in minutes and whether the first piece is compared automatically afterwards.
First, minimum starting torque and resolution. Breakout torque on an M0.8 screw often falls between 0.02 and 0.06 N·m, so resolution needs to be around 0.001 N·m to be meaningful, and a driver whose minimum starting torque exceeds 0.02 N·m is effectively unusable at this size.
Second, bit capability. Shank no larger than 1.6 mm, usable length 40 to 60 mm, runout under 0.02 mm, and fast changeover — head styles are not standardised across single-use devices, and cross, hex and Torx turning up in the same incoming lot is normal.
Third, screw capture. A screw dropped into an 8 mm cavity will at best score the insertion tube and at worst crush the image module, scrapping the unit. Capture means vacuum pickup with per-screw counting, and the capture rate should be specified as complete rather than as a sampling yield.
Fourth, low speed and impact control. No impact load is acceptable in front of an optical surface, so Z-axis contact speed has to be limited to a few millimetres per second and the machine must stop on an abnormal torque rise instead of pushing harder. These four belong in the technical agreement as numbers rather than as "high precision, low torque", and an M0.8-M2.0 screw removal solution normally writes breakout band, cam-out threshold and capture method into the process card so shifts stop improvising.
Related Articles
/ RECOMMENDED NEWS