China Region Telephone

18688976300
News
Service Hotline

18688976300

Mobile: 18688976300 (Mr. Peng) 15222276387 (Mr. Bai)

Email: pengwl@honred.com

QQ: 176496342

Address:Building A1, Runteng Industrial Park, Shiyan Street, Bao'an District, Shenzhen

Screws in a Servo Drive Are Not Just Fasteners: How Power-Module Torque Sets Thermal Resistance and Rework Cost

Date: 2026-11-19       Views: 7

Bottom line first: the screws holding a power module in a servo drive or inverter carry no current, yet they set the interface pressure between module and heatsink, and that pressure rewrites contact thermal resistance, junction temperature and device life. Rising power density has pushed the same package to higher current, so a handful of screws that used to be "tighten and go" have become process parameters governed by torque, sequence and angle curve.

The screw is the first gate on the thermal path

Heat from a power module has only one route out: die, solder layer, ceramic substrate, thermal interface, heatsink. The pressure across that interface comes entirely from the screws. Contact resistance versus interface pressure is not linear: it is highly sensitive at low pressure and saturates quickly at high pressure, so engineering looks for the knee of the curve rather than the maximum. Thermal grease sits at 50 to 100 microns typically, and the largest drop in resistance comes between 0.2 and 0.5 MPa; pushing past 1 MPa buys a few percent while raising the risk of substrate cracking.

The opposite failure is just as common. At excessive torque, an alumina or aluminium-nitride substrate concentrates stress around the screw hole. It starts as a micro-crack and propagates into a through-crack after a few hundred thermal cycles, showing up as intermittent breakdown or gate loss. Factory tests almost never catch this; it surfaces after months in the field, and by then the assembly torque record is usually gone.

The torque window is squeezed from two sides

The first side is thread strength in the heatsink. Most drive heatsinks are die-cast or extruded aluminium with threads cut directly into the metal, and an M3 thread in aluminium needs an effective engagement of at least two diameters to approach the load capacity of steel. Aluminium threads also wear under repeated assembly: after five or more cycles at the same hole, torque retention starts to fall noticeably. The common field remedy is a wire thread insert, which brings its own concentricity deviation.

The second side is multi-point staged tightening. A module usually carries four to six screws; driving them to full torque in one pass pulls the substrate flat by force, leaves residual stress in the interface, and produces uneven grease thickness along the length. Measured thermal resistance twenty percent above design is not rare. The standard sequence is three stages: thirty percent in a diagonal pattern, sixty percent in the same pattern, then full torque in the same order, with a few seconds between stages for stress to relax. Torque and angle are logged together, and an abnormal rise in the curve usually means a damaged thread or debris in the hole.

The driver board, current sensors and bus sensing board around the module typically use M1.6-M2.0 machine or self-tapping screws in tight spaces with slender bosses, where both assembly and rework are prone to cam-out. The window at this size is a fraction of a newton-metre, beyond the repeatability of an ordinary electric driver, so production relies on the low-torque control of small screw removal equipment rather than operator feel.

Rework disassembly: opening it is not the same as closing it

Power-module rework has three hard constraints, and a module that fails any of them should not return to the line. First, the interface material must be replaced entirely: once opened, the grease has pumped out, picked up particles and partly cured, so cleaning and re-applying is the only acceptable route. Second, aluminium thread wear must be assessed: if the breakout curve idles at first and then jumps, the thread is damaged and needs an oversize tap or an insert. Third, removed screws should not be reused, especially on modules that have seen many thermal cycles, because their preload is already relaxed.

Breakout torque normally exceeds assembly torque, and not only because of threadlocker: micro-welding between steel screw and aluminium thread, plus grease migrating into the thread zone at temperature, both add drag. The removal station therefore cannot inherit the assembly torque limit. It needs its own breakout band and must stop rather than force through, since forcing usually ends in a rounded head and a thread-extraction job that puts the module body at risk.

Pre-removal condition checks matter just as much. Whether the module has bulged, whether heads are corroded or carry adhesive residue, whether neighbouring components block the bit path — all of it decides the removal route. Vision earns its place here by imaging every screw position and head condition before choosing a bit and an approach direction. On a high-mix rework line, an automatic vision screw removal machine solves the "three module types on one station today" problem of locating and changeover rather than replacing torque judgement.

Three numbers the removal station has to deliver

Making drive rework a stable operation needs verifiable numbers in three areas. First, torque and angle monitored together, recording peak torque, snug-point angle and total rotation per screw, so normal breakout can be separated from a seized thread and a screw that was never there. Second, screw capture and foreign-object control: every removed screw is collected and counted on the spot, because one screw inside the module cavity can short the DC bus, and capture rate should be specified as complete. Third, traceability: module serial number, breakout parameters and the batch of replacement interface material must map to each other, which is the precondition for a reworked unit to re-enter stock.

For drives already running in production these three usually matter more than cycle time. Small fasteners in the M0.8-M2.0 band make up a meaningful share of rework, and an M0.8-M2.0 screw removal solution normally writes breakout band, cam-out threshold and screw capture method into the process card so shifts stop improvising.