China Region Telephone

18688976300
News
Service Hotline

18688976300

Mobile: 18688976300 (Mr. Peng) 15222276387 (Mr. Bai)

Email: pengwl@honred.com

QQ: 176496342

Address:Building A1, Runteng Industrial Park, Shiyan Street, Bao'an District, Shenzhen

Safety Guarding on a Screw Removal Station: Light-Curtain Distance, Guard Locking and Two-Hand Control

Date: 2026-11-19       Views: 6

Bottom line first: the hazard on a screw removal station is not only the rotating spindle. The vertical down-stroke, the workholding clamp and flying screws are hazards in their own right, so guarding has to follow a risk assessment rather than a single light curtain. Most plants check during acceptance whether a light curtain exists, and rarely check whether it is mounted at the correct distance or whether the circuit actually stops the machine. The difference decides whether the guard is protection or decoration.

Risk assessment first, device selection second

The order is assessment before selection; reversing it usually produces an expensive solution that does not match the hazard. Three hazard families need evaluating: crushing and shearing from the Z-axis down-stroke, entrapment and winding from the rotating spindle, and ejection of screws or a broken bit at the moment of breakout. Add the closing motion of the clamp and hand positions during loading, and the list is essentially complete.

The assessment delivers two outputs: the performance level each hazard requires, and the operating modes that are permitted. Down-stroke and clamping, which can cause irreversible injury, normally call for a safety function at PL d, while warnings and signage are information measures that cannot be counted as a safety function. Once the assessment is done, some stations turn out to be missing not a light curtain but a dual dump valve on the clamp cylinder, so the fixture cannot stay pressurised after power loss.

Light curtains: the distance is calculated, not guessed

Mounting distance must be calculated, because a guard at the wrong distance provides no protection. The general approach uses the minimum distance formula: approach speed multiplied by total system response time, plus an additional allowance set by resolution. Approach speed is taken as 2000 mm per second up to 500 mm and 1600 mm per second beyond that; the allowance shrinks as resolution gets finer.

Total response time has three parts: the curtain's own response, the processing time of the safety relay or safety PLC, and the time the machine needs from receiving the stop signal to the hazardous motion actually ceasing. The third is the most often underestimated. A loaded spindle may need several hundred milliseconds to coast down, and that travel must be covered in the distance. Many installations sit too close to the hazard point because only the first two parts were counted.

A second common problem is misuse of muting and blanking. Fixed blanking to let workpieces pass is logical, but if the blanked zone covers the operator's reach, the guard is defeated. The workable approach restricts the blanked zone to the conveyor width and limits Z-axis speed to a safe value while muting is active. The opening on small screw removal equipment is usually small, so a curtain combined with mechanical guarding is more realistic than simply making the curtain larger.

Guard locking and two-hand control: two interlocks, not interchangeable

Guard locking applies to openable guards; two-hand control applies where there is no guard but both hands must be clear of the hazard zone. Their conditions of use cannot be swapped. The essential property of guard locking is the lock itself: the guard must not release until motion inside has fully stopped, otherwise an operator can open the door while the spindle is still coasting. A locking interlock needs its own holding-force specification and must survive a defined number of forced-opening attempts, which is what separates industrial-grade from commercial-grade devices.

The critical parameter for two-hand control is the synchronisation window. Standard practice requires both buttons to be pressed within 0.5 seconds to be accepted; beyond that window both must be released and the sequence restarted, and releasing either button drops the output immediately. A condition where one button is held down while the other is repeatedly tapped must be logically prohibited, otherwise operators will weight one button with a knee or a fixture.

Note that two-hand control protects only the operator's hands, not a third party. If someone else can reach into the station, two-hand control cannot be the only measure and must be supplemented by mechanical guarding or area scanning. Vision-equipped machines need an operator inside the station for changeover teaching, and that action itself requires a separate authorised reduced-speed routine. The teaching mode on an automatic vision screw removal machine typically requires a held enabling switch and low speed precisely so that human access stays controlled.

E-stops and residual risk: the button is not the answer

The emergency stop is a supplementary measure, never a substitute, and this is where acceptance checks most often go wrong. Its job is to remove hazardous energy quickly when something goes wrong; it cannot stop an operator reaching into the hazard zone and cannot compensate for a miscalculated curtain distance. The stop category follows the risk assessment: removing power and letting motion coast is category 0, controlled deceleration to a stop is category 1, which is gentler on mechanics but needs a braking circuit.

Residual risk usually takes more effort than the primary guard. Flying screws are the classic case: a screw released under rotation carries kinetic energy, and a viewing window in polycarbonate will embrittle and crack under repeated impact. Bit breakage is even harder to predict in direction, and the practical remedy is a flexible skirt around the bit that keeps fragments inside the station. Noise and oil mist belong to occupational health and need separate measures; a light curtain will not address them.

One more residual risk comes from maintenance itself. Safety functions are often bypassed temporarily during manual debugging, and if the bypass switch sits within easy reach it becomes routine practice. The reasonable approach requires a key or permissioned password, and permits only inching, not continuous running, while bypassed.

Acceptance: five actions that can be tested

Turning safety functions into testable actions beats writing "compliant" in a document. Five items are worth measuring: block any point of the curtain and confirm the Z-axis stops within the stated response time, verified frame by frame on video; open the guard and confirm the spindle is fully stopped before the lock releases; press only one two-hand button and confirm the machine does not start, and confirm it also refuses when the interval exceeds the synchronisation window; press the E-stop and confirm all hazardous motion stops and does not restart on reset; enter teaching mode and confirm speed is limited and a held enabling switch is required.

Only when all five pass is the safety circuit proven to be connected and actually acting, rather than merely mounted on the frame. On stations handling M0.8-M2.0 fasteners the emphasis often shifts from entrapment toward ejection and pinch protection, and an M0.8-M2.0 screw removal solution that ships its safety function list and response times with the documentation removes most of the back-and-forth at acceptance.